banner



Home  ›  How To Repair A Rubber Seal

How To Repair A Rubber Seal

Written By Thursday, February 17, 2022 Add Comment Edit

  • Remove the soda bottle and the CO2 canister from the machine. Remove the soda bottle and the CO2 canister from the machine. Remove the soda bottle and the CO2 canister from the machine.

    • Remove the soda bottle and the CO2 canister from the machine.

    • Remove the four 17.8 mm spiral from the bottom metal base using a Phillips #1 screwdriver.

  • Pull the outer cover away from the front of the device. Pull the outer cover away from the front of the device.

    • Pull the outer comprehend away from the front of the device.

    • Remove the two eighteen.2 mm screws from the lesser of the forepart cover using a Phillips #1 screwdriver.

    • Firmly pull the front encompass off.

    • This piece is difficult to remove and requires strength. Information technology may help to use a broad, thin object to pry it off (like a Jimmy).

  • Push the gold bar, located in the top of the device, out of the carbonating block. You can use the end of your screwdriver to push this piece out. You can use the end of your screwdriver to push this piece out.

    • Push the gold bar, located in the acme of the device, out of the carbonating cake.

    • You can use the finish of your screwdriver to push this slice out.

  • Slide the yellow battery cover up and away to remove it from the device. Slide the yellow battery cover up and away to remove it from the device. Slide the yellow battery cover up and away to remove it from the device.

    • Slide the yellowish battery cover up and abroad to remove information technology from the device.

  • Unhook the bottom piece of the plastic arm on each side of the device. Unhook the bottom piece of the plastic arm on each side of the device.

    • Unhook the bottom piece of the plastic arm on each side of the device.

  • Lift the top of the plastic arm with the spudger and remove it on both sides. Lift the top of the plastic arm with the spudger and remove it on both sides.

    • Lift the top of the plastic arm with the spudger and remove it on both sides.

  • Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger. Remove the plastic piece, located near the front of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.

    • Remove the plastic piece, located well-nigh the forepart of the carbonating block, from both sides of the device using a plastic opening tool or nylon spudger.

  • Remove the plastic oval and the spring within it. Remove the plastic oval and the spring within it.

    • Remove the plastic oval and the spring within it.

  • Pull the loader tab cover down and away from the rest of the carbonating block. Pull the loader tab cover down and away from the rest of the carbonating block.

    • Pull the loader tab cover downwardly and abroad from the rest of the carbonating block.

  • Remove the three 17.9 mm screws located on the right side.

    • Remove the three 17.9 mm screws located on the right side.

    • These screws may be difficult to access.

  • Unhook the four clips on the top of the carbonating block and remove the plastic cover. Unhook the four clips on the top of the carbonating block and remove the plastic cover.

    • Unhook the 4 clips on the top of the carbonating block and remove the plastic comprehend.

  • Lift the clips located on both sides with the plastic spudger. Slide the front cover off. Lift the clips located on both sides with the plastic spudger. Slide the front cover off. Lift the clips located on both sides with the plastic spudger. Slide the front cover off.

    • Lift the clips located on both sides with the plastic spudger. Slide the front cover off.

  • Unhook the silver spring arms on both sides of the device by pushing down. Unhook the silver spring arms on both sides of the device by pushing down.

    • Unhook the silver spring arms on both sides of the device by pushing down.

  • Grip the right and left sides of the device and pull it into two identical halves.

    • Grip the right and left sides of the device and pull it into two identical halves.

    • Once these two pieces are apart, all remaining internal components volition autumn out of the device.

  • Pull the foam pad up and remove it from the front side of the carbonation component. Pull the foam pad up and remove it from the front side of the carbonation component. Pull the foam pad up and remove it from the front side of the carbonation component.

    • Pull the foam pad up and remove information technology from the forepart side of the carbonation component.

  • Remove the six 17.7 mm screws from the underside of the loader tab piece.

    • Remove the six 17.vii mm screws from the underside of the loader tab piece.

  • Pull the loader tab out of the nozzle. Pull the loader tab out of the nozzle. Pull the loader tab out of the nozzle.

    • Pull the loader tab out of the nozzle.

  • Remove the rubber seal from the nozzle piece and replace with the new seal. Remove the rubber seal from the nozzle piece and replace with the new seal.

    • Remove the safety seal from the nozzle piece and replace with the new seal.

    • Source: https://www.ifixit.com/Guide/SodaStream+Source+Internal+Rubber+Seal+Replacement/87403

    Posted by: daubdasked1981.blogspot.com

    0 Response to "How To Repair A Rubber Seal"

    Post a Comment

    Subscribe to: Post Comments (Atom)

    Iklan Atas Artikel

    Iklan Tengah Artikel 1

    Iklan Tengah Artikel 2

    Iklan Bawah Artikel